U-Line CLR2160 Průvodce řešením problémů stáhnout pdf (Strana 13)

CLR2160, CLRCO2175 13

it from the drain hole. The water in the reservoir will

flow down the drain.

5. Replace the overflow tube after all of the water has

drained from the reservoir.

6. Start the cleaning cycle as follows:

a. Touch and hold the ON/OFF button (Figure 9, 1).

b. Touch and release the LIGHT button (Figure 9, 4)

three times, then release the ON/OFF button

(Figure 9, 1).

c. The display (Figure 9, 3) will show “CL” to confirm

the beginning of the cleaning cycle.

7. When water begins to flow over the evaporator

(approximately three minutes), add one package of U-

Line Ice Machine cleaner to the water reservoir.

8. Reinstall inside front cover.

9. When the self-cleaning process stops (approximately 45

minutes) the unit will remain off for an additional 15

minutes. When clean cycle is completed, display will

automatically switch back to set temperature and unit

will run as normal operation.

10. Clean the storage bin (See INTERIOR CLEANING).

Sanitize the bin with a solution of 1 tablespoon of

bleach in 1 gallon of warm water. Rinse thoroughly

with clean water.

11. To ensure that the drain system is working properly,

pour 1 gallon of cool, fresh water into the ice bin. The

water should drain freely. If your unit is equipped with

a drain pump, it should drain the ice bin.

When ice production resumes, the water fill valve will

energize, fill the water reservoir, and shut-off after three

minutes. The compressor begins to operate and water

flows over the evaporator assembly (ice cube tray).

Initially, the water flow may not be uniform, causing

uneven sized cubes or water to spill into the ice storage

bin. This is a normal situation that will correct itself within

the first 24 hours of operation.

IMPORTANTIMPORTANT

• Discard all ice produced in the first harvest.

• Should power to the unit be interrupted during

the self-clean cycle, it will be necessary to repeat

the complete cleaning cycle after power is

restored.

Inlet Screen

Interval - Every Twelve Months

The solenoid valve inlet screen must be cleaned at least

once each year as follows:

1. Shut off the water at the main supply valve.

2. Pull the unit out to access the back panel.

3. Disconnect electrical power to the unit.

Figure 12

4. Disconnect the hose connector

(Figure 12, 1)

from the

water solenoid valve

(Figure 12, 2)

5. DO NOT remove the inlet screen

(Figure 12, 3)

from

the water solenoid valve. Use a toothbrush to gently

clean any sediment from the inlet screen.

6. Re-connect the water supply hose connector

(Figure

12, 1)

to the water solenoid valve

(Figure 12, 2)

Tighten the connector securely.

7. Open the water main supply valve and check for leaks

at the water hose connection. Ensure that the water

supply line is not kinked.

8. Reconnect power to the unit before re-installing.

9. Make sure the drain system is working properly and the

drain hose is not pinched or kinked. Pour 1 gallon of

cool, fresh water into the ice bin. The water should

drain freely. If your unit is equipped with a drain pump,

the pump should drain the ice bin.

10. To ensure that the drain system is working properly,

pour 1 gallon of cool, fresh water into the ice bin. The

water should drain freely. If your unit is equipped with

a drain pump, it should drain the ice bin.

Ice Cube Thickness Adjustment

Interval - As Required

Ice thickness adjustments are made using the control

panel as follows:

Figure 13

1. To enter the thickness adjustment mode:

a. Touch and hold the UP ARROW button (Figure

13, 1).

ULIN_0061_A

ULIN_0200_A

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 23 24

Komentáře k této Příručce

Žádné komentáře

U-Line CLR2160 Průvodce řešením problémů Strana 13

Komentáře k této Příručce

Související produkty a manuály pro Ledničky U-Line CLR2160